Galletto 4 - V54
FGtech Galletto 4 Master V54 - Full Chip 0475: Engine ECU programmer via OBD or on table.
The GALLETTO is a simple tool that allows you to read and write original or modified files in the vehicle's ECU through its OBD 2 socket in a few minutes. It communicates with a wide range of ECUs, even the latest generation, and allows you to read and write directly to the ECU microprocessor, flash memory and EEPROM.
With an intuitive interface, it really aims to simplify handling for professionals and amateurs alike.
You will be able to master the entire reprogramming in a few minutes.
When the OBD2 socket cannot be used for reading and writing, the GALLETTO is equipped with the cables for a table connection (BDM JTAG).
First you read the files inside the ECU using GALLETTO, then you have your file modified by a professional and finally you write them back to the ECU.
Programming Flexfuel BioEthanol with the GALLETTO:
The GALLETTO allows you to transform your petrol vehicle equipped with multipoint injection into Flex fuel
It will thus be able to run on SP95 / SP98 or E85 Super-Ethanol, without adding any additional box.
The transformation is quick, simple, economical and completely invisible to technical control or the garage. You'll get your next fill-up at half price!
Power and torque programming:
You are probably interested in programming a Stage 1, a Stage 2 or handling EGR, FAP, SCR, Adblue, Limiters, etc. valve options.
Gain in performance, in pleasure and lower your consumption for a derisory cost
Reprogram your engine ECU but also that of your friends, or start a new activity, there is no limit of use
GALLETTO Master Version:
Full recovery mode
Default DTC error analysis and removal tool
Monitor battery voltage in real time
Etc ...
Main advantage of the GALLETTO:
- GALLETTO is able to write via OBD and via Tricore BDM
- GALLETTO is ultra-compact
- Its software launches without having to connect to a vehicle
GALLETTO compatibility:
- With many cars, light commercial vehicles, trucks, tractors, boats, etc...
- Communication protocols with ECUs up to 2012.
GALLETTO protocols:
NEW JTAG - BDM - MOTOROLA - FREESCALE – INFINEON
Freescale MPC 5553/5554/5565/5566 NEXSUS PORT New IAW MJD 8F2
Delphi DCM3.5xx DCM3.7xx TRW
Motorola Freescale MPC 555 / 556 / 561 / 562 / 563 / 564 / 565
Motorola MC 68332 - MC YQQCU - MC 68377 Trionic 5 / 7 / 8 GM-OPEL-SAAB
Motorola MC68376-01 Lamborghini-Lotus
Motorola MC 68336 MEMS D5 ROVER
Motorola ZC 439615 - ZC 439507 IAW FIAT - VAG
VPM GM - Hummer-Corvette-Munstang-Blazer-Cadilac
Tx-Rx-Subaru-Mitsubishi-Hitachi-Denso ECU
All EDC17 MED17 in Boot Mode.
Automatic Calculation of Checksum:
All old protocols are included: Bosch MExx / EDCxx / Marelli / Siemens / Delphi / Lucas / Denso
Boot Mode C167x/ST10
Boot Mode Infineon with password Bosch/Siemens
Motorola MC68332 - MCYQQCU - MC68377 - MC68376 - MC6833 - ZC439615 - ZC439507
Motorola Freescale MPC 555 / 556 / 561 / 562 / 563 / 564 / 565
Freescale MPC 5553 / 5554 / 5565 / 5566
BDM
Industrial vehicles:
K-line, KWP, CAN
Can Bus V2.0 50Kb > 1000Kb
J1850 VPW PWM GM - FORD
Rx Tx RS232
RS 485
K-line 250, 500, 1000 ohm,
Automatic Can Bus 0, 60,120 ohms
Consult the manual, the compatibility list of vehicles, motorcycles, trucks, buses... as well as the various protocols supported by the GALLETTO in the "attached documents" section.
Contents of the GALLETTO package:
1x FGTech GALLETTO 4 interface
1x Cable for boot ECU
1x Adapter for BDM
3x BDM Adapters
6x BDM Connectors
1x OBD2 Cable
1x USB cable
1x EOBD2 Software CD
GALLETTO works only under Windows XP and Windows 7 in 32 bits
NOTICE! Read this imperatively before buying!
This software is intended for professional use only. We do not provide any educational content or technical support to avoid incorrect use of files.
We assume no responsibility for misuse of software or files, as well as for any damage caused to your ECU due to use of incorrect files or handling errors.
If you are unsure whether you can use this software/tool ​​correctly, we recommend that you do not make this purchase.